Like just about everything else, there’s a right way and a wrong way to thaw frozen pipes. Here are a few tips to keep your pipes from freezing in the first place. We also have some advice for thawing a pipe that’s already frozen.
Keep your pipes from freezing
The best way to deal with frozen pipes is to avoid them altogether. Heating your home can be expensive, and it’s tempting to “dial down” at night and when you’re not around. When the air temperature is super-cold (below freezing), your pipes can be at risk.
Pipes break when the water inside them freezes. Most plumbing is rigid, so the pipes are full of standing water when the taps are closed. This is good because a pipe that’s full of water doesn’t have any air. Air in the system could allow bacteria to thrive, and it could also change the water pressure.
Unfortunately, water expands when it freezes. In an open container, the freezing water has “head space” – room to expand. In a water pipe, there is no room for expansion. An ice blockage forms somewhere in your pipe and begins to exert enormous pressure – as high as 2,000 PSI – on the unfrozen water between the blockage and the tap. Traditional plumbing does not have enough material strength to hold back this unrelenting pressure. As the blockage grows, the pressure increases. Because the pipe is rigid, it cannot expand enough, and it will deform and split somewhere to relieve the pressure. The first thing you can do to avoid frozen pipes is to keep your pipes warm! Insulate them to prevent cold air intrusions from affecting your pipes. Open sink cabinet and vanity doors to allow warmer air to circulate around your pipes. Open heat registers in the basement (if your pipes are below-grade) to let more warm air circulate around them. Don’t turn the heat down when it’s super-cold outside. Yes, your utility bill will go up, but a higher heating bill beats flooding, water damage and mold.
Managing a frozen pipe
If a pipe freezes and it’s accessible, open the tap immediately to drain any water from the pipe. This may relieve some of the pressure, but you’re not out of the woods yet. Start warming the pipe from the tap and work your way toward the blockage. A good safe heat source is an incandescent light bulb. A hair dryer may also help loosen up a frozen pipe. Be especially careful if you use “heat tape.” Used incorrectly, it can cause a fire!
DO NOT USE AN OPEN FLAME TO THAW A FROZEN PIPE! That includes welding and soldering torches, cigarette lighters, charcoal lighters, tiki torches, candles or anything else fiery. Open flames caused 30% of house fires in 2017. It’s just not a good idea!
You may not initially know that a pipe has frozen, but lack of water should set off alarm bells! If you get no water from a tap, or a water appliance stops working, If you open a tap and get just a trickle of water – your pipe is in the process of freezing. Act fast to relieve the pressure and correct the problem. On the other hand, you may know your pipe has frozen because it has already split and there’s water everywhere! In this case, turn off the water to that segment of pipe and begin the process of thawing. Start drying out anything that’s gotten wet. You may have to remove drywall, plaster, carpeting or flooring. You won’t be able to turn the water back on until the pipe is repaired, but at least you can limit the water damage.
Following up on a frozen pipe
Maybe you were able to get your pipe thawed out before it split. That’s a lucky break, but your pipe is probably still damaged. The pressure can weaken and deform your pipe – and maybe not in the place(s) you’d expect. Remember, 2,000 PSI is about 20 times the pressure your pipes are designed to handle.
Inspect your pipes for deformed joints, bulges, discolorations, little drips or anything generally weird-looking. Formerly frozen pipes that “burst” usually have a little slit someplace, often somewhere other than where the blockage formed. It will look like someone took a box cutter and made a slice in the pipe. (You’ll be able to find these more easily, because water will be spraying all over the place!) Don’t forget to check any PEX hoses that supply water to toilets, sinks and appliances. These can freeze too! PEX resists freezing, but the fittings can get damaged. If you find a frozen PEX hose, take comfort in the fact that they’re cheap to replace.
If you’ve experienced a frozen pipe, or need help repairing freeze-damaged plumbing, contact us at Boston Standard Company at (617) 362-0377
. We’ll be happy to help!
Photo Credit: Cynthia Closkey, via Flickr
Categories:
DIY Blog, DIY Heating, DIY Plumbing, Hose Spigot, Plumbing, Tips and Tricks